/**
  @Generated PIC10 / PIC12 / PIC16 / PIC18 MCUs Source File

  @Company:
    Microchip Technology Inc.

  @File Name:
    mcc.c

  @Summary:
    This is the device_config.c file generated using PIC10 / PIC12 / PIC16 / PIC18 MCUs

  @Description:
    This header file provides implementations for driver APIs for all modules selected in the GUI.
    Generation Information :
        Product Revision  :  PIC10 / PIC12 / PIC16 / PIC18 MCUs - 1.65.2
        Device            :  PIC16F1579
        Driver Version    :  2.00
    The generated drivers are tested against the following:
        Compiler          :  XC8 1.45 or later
        MPLAB             :  MPLAB X 4.15
*/

/*
    (c) 2018 Microchip Technology Inc. and its subsidiaries. 
    
    Subject to your compliance with these terms, you may use Microchip software and any 
    derivatives exclusively with Microchip products. It is your responsibility to comply with third party 
    license terms applicable to your use of third party software (including open source software) that 
    may accompany Microchip software.
    
    THIS SOFTWARE IS SUPPLIED BY MICROCHIP "AS IS". NO WARRANTIES, WHETHER 
    EXPRESS, IMPLIED OR STATUTORY, APPLY TO THIS SOFTWARE, INCLUDING ANY 
    IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY, AND FITNESS 
    FOR A PARTICULAR PURPOSE.
    
    IN NO EVENT WILL MICROCHIP BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, 
    INCIDENTAL OR CONSEQUENTIAL LOSS, DAMAGE, COST OR EXPENSE OF ANY KIND 
    WHATSOEVER RELATED TO THE SOFTWARE, HOWEVER CAUSED, EVEN IF MICROCHIP 
    HAS BEEN ADVISED OF THE POSSIBILITY OR THE DAMAGES ARE FORESEEABLE. TO 
    THE FULLEST EXTENT ALLOWED BY LAW, MICROCHIP'S TOTAL LIABILITY ON ALL 
    CLAIMS IN ANY WAY RELATED TO THIS SOFTWARE WILL NOT EXCEED THE AMOUNT 
    OF FEES, IF ANY, THAT YOU HAVE PAID DIRECTLY TO MICROCHIP FOR THIS 
    SOFTWARE.
*/

// Configuration bits: selected in the GUI

// CONFIG1
#pragma config FOSC = INTOSC    // Oscillator Selection Bits->INTOSC oscillator; I/O function on CLKIN pin
#pragma config WDTE = OFF    // Watchdog Timer Enable->WDT disabled
#pragma config PWRTE = OFF    // Power-up Timer Enable->PWRT disabled
#pragma config MCLRE = OFF    // MCLR Pin Function Select->MCLR/VPP pin function is digital input
#pragma config CP = ON    // Flash Program Memory Code Protection->Program memory code protection is enabled
#pragma config BOREN = OFF    // Brown-out Reset Enable->Brown-out Reset disabled
#pragma config CLKOUTEN = OFF    // Clock Out Enable->CLKOUT function is disabled. I/O or oscillator function on the CLKOUT pin

// CONFIG2
#pragma config WRT = ALL    // Flash Memory Self-Write Protection->000h to FFFh write protected, no addresses may be modified by EECON control
#pragma config PPS1WAY = ON    // PPSLOCK bit One-Way Set Enable bit->PPSLOCKED Bit Can Be Cleared & Set Once
#pragma config PLLEN = OFF    // PLL Enable->4x PLL disabled
#pragma config STVREN = OFF    // Stack Overflow/Underflow Reset Enable->Stack Overflow or Underflow will not cause a Reset
#pragma config BORV = LO    // Brown-out Reset Voltage Selection->Brown-out Reset Voltage (Vbor), low trip point selected.
#pragma config LPBOREN = OFF    // Low Power Brown-out Reset enable bit->LPBOR is disabled
#pragma config LVP = OFF    // Low-Voltage Programming Enable->High-voltage on MCLR/VPP must be used for programming